在啟動天然氣發電機組前，需要做好以下關鍵事項，以確保機組安全、穩定地運行。

Before starting the natural gas generator unit, the following key matters need to be done to ensure the safe and stable operation of the unit.

一、天然氣發電機組外觀與連接檢查

1、 Appearance and connection inspection of natural gas generator set

天然氣發電機組外觀：

Appearance of natural gas generator set:

檢查機組整體外觀是否有損壞、變形或銹蝕現象。

Check the overall appearance of the unit for any damage, deformation, or rust.

確保機組各部件連接牢固，無松動或脫落情況。

Ensure that all components of the unit are securely connected without any looseness or detachment.

電氣連接：

Electrical connection:

檢查電氣線路和接頭的連接是否牢固，無松動、腐蝕或破損現象。

Check if the electrical circuits and connectors are securely connected, without any looseness, corrosion, or damage.

確保電纜絕緣層完好，無裸露或破損。

Ensure that the insulation layer of the cable is intact, without any exposure or damage.

二、天然氣發電機組燃料系統檢查

2、 Fuel system inspection of natural gas generator set

天然氣供應：

Natural gas supply:

確認天然氣供應管道暢通，無泄漏現象。

Confirm that the natural gas supply pipeline is unobstructed and there are no leaks.

檢查天然氣壓力是否穩定，符合機組要求。

Check if the natural gas pressure is stable and meets the requirements of the unit.

確保天然氣過濾器清潔，無堵塞。

Ensure that the natural gas filter is clean and unobstructed.

閥門與調節器：

Valves and regulators:

檢查天然氣閥門是否開啟靈活，無卡滯現象。

Check whether the natural gas valve opens flexibly without any jamming phenomenon.

確認燃氣調節器工作正常，能夠穩定調節燃氣流量。

Confirm that the gas regulator is working properly and can stably regulate the gas flow rate.

三、天然氣發電機組潤滑系統檢查

3、 Inspection of lubrication system for natural gas generator set

天然氣發電機組機油油位：

Oil level of natural gas generator set:

檢查機油油位是否在油尺的FULL與ADD刻度之間。

Check if the oil level is between the FULL and ADD marks on the dipstick.

如機油不足，應及時添加至規定油位。

If the engine oil is insufficient, it should be added to the specified oil level in a timely manner.

機油質量：

Oil quality:

檢查機油是否變質，如機油顏色變暗、有雜質或異味，應及時更換。

Check if the engine oil has deteriorated. If the color of the oil becomes darker, there are impurities or odors, it should be replaced in a timely manner.

四、天然氣發電機組冷卻系統檢查

4、 Inspection of cooling system for natural gas generator set

天然氣發電機組冷卻液存量：

Coolant inventory of natural gas generator set:

檢查冷卻液存量是否充足，如不足應及時添加。

Check if the coolant inventory is sufficient, and add it promptly if it is insufficient.

確保冷卻液質量良好，無雜質或沉淀物。

Ensure that the coolant is of good quality and free from impurities or sediment.

冷卻系統管路：

Cooling system piping:

檢查冷卻系統管路是否暢通，無泄漏或堵塞現象。

Check if the cooling system piping is unobstructed, without any leaks or blockages.

確保散熱器清潔，無灰塵或雜物堆積。

Ensure that the radiator is clean and free from dust or debris accumulation.

五、天然氣發電機組進氣與排氣系統檢查

5、 Inspection of the intake and exhaust systems of natural gas generator sets

空氣濾清器：

Air filter:

檢查空氣濾清器是否清潔，如有必要進行清理或更換。

Check if the air filter is clean, and if necessary, clean or replace it.

確保進氣管道暢通，無堵塞或泄漏現象。

Ensure that the intake duct is unobstructed and free from blockages or leaks.

排氣系統：

Exhaust system:

檢查排氣管道是否暢通，無堵塞或泄漏現象。

Check whether the exhaust pipe is unobstructed, without blockage or leakage.

確保消聲器工作正常，無異常噪音。

Ensure that the muffler is functioning properly and without any abnormal noise.

六、天然氣發電機組控制系統與安全裝置檢查

6、 Inspection of Control System and Safety Devices for Natural Gas Generator Sets

控制系統：

Control system:

檢查控制系統的各項參數設置是否正確。

Check whether the various parameter settings of the control system are correct.

確認控制面板顯示正常，無故障報警。

Confirm that the control panel displays normally and there are no fault alarms.

安全裝置：

Safety device:

檢查超溫保護、超速保護、低油壓保護等安全裝置是否靈敏可靠。

Check whether the safety devices such as over temperature protection, over speed protection, and low oil pressure protection are sensitive and reliable.

確保緊急停機按鈕功能正常，能夠在緊急情況下迅速停機。

Ensure that the emergency stop button functions properly and can quickly shut down in emergency situations.

七、天然氣發電機組啟動前測試與準備

7、 Pre start testing and preparation of natural gas generator sets

預潤滑：

Pre lubrication:

對于需要預潤滑的天然氣發電機組，在啟動前應進行預潤滑操作，以確保機組各部件得到充分潤滑。

For natural gas generator sets that require pre lubrication, pre lubrication should be performed before starting to ensure that all components of the unit are fully lubricated.

盤車檢查：

Turning inspection:

手動盤車檢查機組各部件是否轉動靈活，無卡滯現象。

Manually rotate and check if all components of the unit rotate smoothly without any jamming.

啟動測試：

Start testing:

在正式啟動前，可進行短時間的啟動測試，觀察機組啟動是否平穩、無異常噪音或振動。

Before the official start-up, a short-term start-up test can be conducted to observe whether the unit starts smoothly, without any abnormal noise or vibration.

本文由工業尾氣發電機組友情奉獻.更多有關的知識請點擊:http://m.seewest.cn真誠的態度.為您提供為全面的服務.更多有關的知識我們將會陸續向大家奉獻.敬請期待.

This article is a friendly contribution from an industrial exhaust gas generator set For more information, please click: http://m.seewest.cn Sincere attitude To provide you with comprehensive services We will gradually contribute more relevant knowledge to everyone Coming soon.